What're your opinions about Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult project. If the old tub is easily available, the job can relocate easily; if you need to open up a wall to remove the old tub and position the new bath tub, the task is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly need an assistant to leave the old tub and set in the new one. Make sure you have actually certified on your own for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your washroom if you have already acquired a new bathtub and do not need to alter the arrangement of your previous water system pipelines.
Your tools and also material list should make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be fairly problematic as a result of the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet connectors. The previous kind should be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water and inspect all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and also check the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is recommended to fit the tiles using waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about Installing A Bathtub. Thank you so much for taking the time to read our article post. Those who liked our page kindly do not forget to share it. Thank you so much for your time spent reading it.
Act before it's late!